Have you ever required to induce more nitty gritty in your troubleshooting of wireless networks simply had to urge down to the bundle level? Some of the time seeing the raw packets in Wireshark gives us all we have to be analyze a problem. With Ruckus Remote you'll be able empower two sorts of parcel captures straight from the net interface of the Ruckus ZoneDirector.

- Local

- Stream

Both modes can be chosen from the AP in which you may be capturing bundles. Local mode will capture parcels two and from the AP and store that capture locally. You at that point download the capture record and open it in Wireshark.

The streaming mode allows you to utilize Wireshark as a farther capture. The AP streams all the parcels to your laptop! In this post I will appear you how to empower parcel capture mode within the Ruckus ZoneDirector for a specific AP and after that stream those bundles to my tablet which is able be running Wireshark. To begin capturing bundles on a Ruckus AP, to begin with log into the ZoneDirector and press on the Administer tab. At that point on the cleared out route press on Diagnostics.

Close the foot of that window you may see a segment labeled Packet Capture. To begin with, select which band you need to capture on, 2.4GHz or 5GHz. At that point, we are going select the APs we need to run in capture mode. You'll be able select more than one AP and do a speedy look in case you have got numerous APs. Check the box following to the AP you need to capture parcels on and after that tap on Add to Capture APs. Each AP you include to Capture APs will show on the proper side. The result is expelled from the list of accessible APs on the left. To start capturing bundles, select the checkbox for the AP and after that select either Neighborhood Mode or Gushing Mode. In this select I chose Spilling Mode.

Then press on Start.

Presently this is often where it starts to induce interesting.This inaccessible capture is as it were accessible on Microsoft Windows since it employments WinPcap. The target area (Ruckus AP) will be running Farther Bundle Capture Convention. Open Wireshark and hit CTRL-K on the console to bring up your Capture Alternatives. At that point tap on Oversee Interfaces. When Interface Administration opens up press on the Farther Interfacing tab and tap Include. Here you may sort within the Have IP address of the Ruckus AP you chosen to ended up a Capture AP. Leaving the Harbour field clear will default to harbour 2002. All other areas can stay at its default option.

 

After you hit Alright it'll include all of the Ruckus APs interfacing to the Capture Choices list. Empower and debilitate the Capture on all interfacing to uncheck everything. Empower the interface with wlan100 for 2.4GHz, or on the off chance that you selected 5GHz hunt for wan101.

Once you begin the capture you may get a stream of bundles from the Ruckus AP.

 
https://mobileinfoworld.com/?p=1706

On the off chance that you're unable to put through to a Windows Server Network Load Balancing (NLB) Virtual IP address designed for Multicast Mode it is since of the way your Cisco switch interatomic with Microsoft NLB.

Symptoms

- Cannot ping Windows Server NLB Virtual IP address

- Cannot connect Windows Server NLB Virtual IP address

- NLB Multicast Mode not working

We would not go into the details of how NLB works, client requests are distributed across different servers. To configure NLB, you can use three modes:

- Multicast

- Unicast

- IGMP

Multicast Mode

When utilizing Multicast mode, the cluster individuals will react to ARPs utilizing their virtual IP address and a multicast MAC address. Without the right configuration on the switch you may not be able to associate to the Virtual IP address.

This will not work because within the ARP request packet is a unicast IP address and a multicast MAC address. Investigating it can be baffling but a Cisco switch will overlook this. Underneath is the arrangement to be done on the switch.

Cisco Switch Configuration

To resolve the issue, make a inactive ARP section for the Virtual IP Address to the NLB MAC address. At that point make a inactive MAC address section to the VLAN and interfacing utilized by the cluster.

In my case, my virtual IP address is 192.168.10.10 with MAC address of 03bf.0a65.05fa. That IP address is on VLAN 10 and the servers' interfacing are portion of a port-channel, both Port-Channel1 and Port-Channel2.

configuration is as follows:

arp 192.168.10.10 03bf.0a65.05fa

mac address-table static 03bf.0a65.05fa vlan 10 interface Port-Channel1 Port-Channel2

A few arrangement things to note.. not all Cisco switches will bolster a inactive passage of a MAC address to numerous interfacing. In my case I am employing a Cisco Catalyst 4500-X in VSS mode. The servers had two arrange interfacing designed into an EtherChannel.
https://mobileinfoworld.com/windows-server-nlb-virtual-ip-address-by-cisco-switch/

Steps to change Trend Micro Internet Security to automatically change the Personal Firewall Profile

The Trend Micro Internet Security Personal Firewall can automatically activate a different profile when your computer changes its network connection. This feature is useful if you move your laptop between your home, your office, and different Wi-Fi hotspots.

To activate this feature, please do the following:

1. Open the TMIS main console by doing any of the following:

Click Start > Programs or All Programs > TMIS > Trend Micro Internet Security.

Double-click it's icon on the lower right corner of your screen.

2. Click Personal Firewall Controls on the left panel.

3. Under Personal Firewall, click Settings.

4. Make sure that the Activate the Personal Firewall checkbox is enabled.

5. Put a checkmark in the Automatically switch to the appropriate firewall profile when you change location checkbox.

6. Click OK to save your settings.

7. Close it's main console.
https://mobileinfoworld.com/?p=4785

Process to Access Windows Live Hotmail with Outlook

Access Free Windows Live Hotmail with Outlook 2003 and Outlook 2007

• Download and install Microsoft Office Outlook Connector.

• Select Outlook Connector | Add a New Account... from the menu in Outlook.

• Type your Hotmail address under E-mail address:.

• Enter your Windows Live Hotmail password under Password:.

• Type your name under Name:.

• Click OK.

• Click OK again.

• Restart Outlook

Access a Windows Live Hotmail Plus Account in Outlook

If you pay for Windows Live Hotmail Plus, you can — in addition to setting up Windows Live Hotmail using Outlook Connector as described above — download mail from your Windows Live Hotmail inbox to Outlook using POP.

To set up Windows Live Hotmail Plus as a POP account in Outlook:

• Select Tools | Account Settings... from the menu in Outlook.

• Go to the E-mail tab.

• Click New....

• Make sure Microsoft Exchange, POP3, IMAP, or HTTP is selected.

• Click Next >.

• Type your name as you want it to appear in outgoing email under Your Name:.

• Enter your Windows Live Hotmail address under E-mail Address:.

• Make sure Manually configure server settings or additional server types is checked.

• Click Next >.

• Make sure Internet E-mail is selected.

• Click Next >.

• Make sure POP3 is selected under Account Type:.

• Enter "pop3.live.com" (not including the quotation marks) under Incoming mail server:.

• Type "smtp.live.com" under Outgoing mail server (SMTP):.

• Enter your complete Windows Live Hotmail address ("example@hotmail.com", for example) under User Name:.

• Type your Windows Live Hotmail password under Password:.

• Click More Settings....

• Go to the Outgoing Server tab.

• Make sure My outgoing server (SMTP) requires authentication is checked.

• Verify Use same settings as my incoming mail server is selected.

• Go to the Advanced tab.

• Make sure This server requires an encrypted connection (SSL) is checked under Incoming server (POP3):.

• Make sure SSL is selected for Use the following type of encrypted connection: under Outgoing server (SMTP):

• Check that "995" appears under Incoming server (POP3:) and "25" under Outgoing server (SMTP):.

• Click OK.

• Now click Next >.

• Click Finish.

• Click Close.

Access Windows Live Hotmail with Outlook 2000 and 2002

To configure Outlook to access your existing Windows Live Hotmail account (you can't set up a new account from within Outlook):

• Make sure you have an subscription for the Windows Live Hotmail account you want to access offline.

• Select Tools | E-mail Accounts... from the menu in Outlook.

• Make sure Add a new e-mail account is selected.

• Click Next.

• Choose HTTP as the Server Type.

• Click Next again.

• Enter your account details in the E-mail Accounts dialog box:

o Type your full name under Your Name:.

o Type your Windows Live Hotmail address under E-mail Address:.

o If Outlook has not entered it for you automatically, type your Hotmail email address User Name:.

o Type your Windows Live Hotmail password under Password:.

o Select Hotmail in the HTTP Mail Service Provider box.

• Click Next.

• Click Finish.
https://mobileinfoworld.com/access-windows-live-hotmail-with-outlook/

Are you having issues together with your wireless network? On the off chance that so, you're not alone. Numerous remote systems in some cases moderate down or temporarily break down.

1. Choose a central location

Central areas give the leading flag scope over your whole building. For two-story structures, in the event that your router or get to point is on the primary floor, place the switch or get to point tall on a rack to supply a more grounded flag for gadgets on the moment floor.

2. Reduce wireless interference

The foremost common remote innovation, 802.11g (wireless-G), works at a recurrence of 2.4 gigahertz (GHz). Numerous remote gadgets such as cordless phones, microwave broilers, infant screens, and carport entryway openers utilize this same recurrence.

3. Replace your wireless network adapter

wireless network signals are sent to and from your computer. Gadgets with built-in remote organizing ordinarily have amazing recieving wires. Now and then, be that as it may, the switch can broadcast to your gadget, but your gadget can't send signals back to the switch. To resolve this issue, supplant your card-based remote organize connector with a USB remote organize connector that employments an outside recieving wire.

4. Add a wireless repeater

Wireless repeaters are handy devices that rebroadcast a wireless signal, strengthening the signal of your router.

5. Upgrade 802.11a, 802.11b, 802.11g devices to 802.11n

When buying new hardware, buy wireless-N innovation. In spite of the fact that wireless-G may be the foremost common remote arrange, wireless-N is at slightest two times as quick. It too has superior extend and steadiness. Wireless-N is in reverse consistent with 802.11a, 802.11b, and 802.11g, meaning you'll still utilize any remote hardware simply as of now claim.
https://mobileinfoworld.com/5-tips-to-improve-your-wireless-network/